optibond.ru создан как площадка для обмена глубоким клиническим опытом

Does composite repair time affect repair protocol, immediate or delayed?

Original PubMed abstract — English. No translation or clinical interpretation.

Authors

Murat Can Ersen; Nevin Cobanoglu

Publication details

BMC oral health · 2025 · Vol. 26 · No. 1 · Pages/article no. 122

Publication date (as recorded): 2025-12-14

PMID: 41398260

Abstract (original)

BACKGROUND: Composite resin restorations frequently require repair due to fractures, marginal defects, or esthetic failures. The effectiveness of composite repair depends heavily on the surface treatment applied prior to bonding. This study aimed to evaluate the effects of various surface treatment protocols on the shear bond strength(SBS) between composite resin layers in same-visit immediate repair(IR) and delayed repair (DR) conditions, using bulk-fill and nanohybrid composite resins. METHODS: Two types of composite resin materials—NeoSpectra ST HV (nanohybrid) and Tetric N-Ceram Bulk-Fill—were tested. A total of ten surface treatment protocols were evaluated under both immediate and delayed repair conditions (n = 10 per subgroup). Following grinding with a diamond bur, the surfaces were treated with one of the following: phosphoric acid, universal adhesives (Single Bond Universal, Prime&Bond Universal), three application modes of Clearfil SE Bond (two-step, bond only without primer, or phosphoric acid application followed by bond only), Optibond FL without primer, or GC Modeling Liquid. Additionally, direct layering without any surface treatment was included as a control. SBS was measured using a universal testing machine, and failure modes were analyzed using a stereomicroscope. One-way analysis of variance and Tukey’s post hoc test were used for statistical analysis (p = 0.05). RESULTS: IR groups showed significantly higher SBS than DR groups across both composite types. The highest SBS were observed with GC Modeling Liquid and hydrophobic bonding agents, particularly in the bulk-fill immediate repair groups. Phosphoric acid application alone, or in combination with self-etch adhesive, did not improve bond strength. Universal adhesives did not outperform hydrophobic agents in any condition. Direct layering without treatment resulted in the lowest bond strength, especially in delayed repair. CONCLUSIONS: Surface treatment protocol significantly affects the success of composite resin repair. Hydrophobic adhesives and GC Modeling Liquid proved to be the most effective options, especially for same-visit immediate repairs. Simplified approaches avoiding unnecessary etching or priming may offer clinically efficient solutions without compromising bond strength.

Source: https://pubmed.ncbi.nlm.nih.gov/41398260/


Rubberdamology
Глобальный аудит

Глобальное сравнение адгезивных систем: IV, V, VI, VII, VIII поколений

Масштабный академический синопсис доказательной базы PubMed. Сравнительный анализ устойчивости гибридного слоя к гидролизу, физика «водных деревьев» в упрощенных бондах и обоснование тотального превосходства многокомпонентного запечатывания дентина в рамках стандартов RSBC.

OptiBond FL
Глобальный аудит

Полный реестр научных статей о применении OptiBond FL

Массив в 401 исследование по OptiBond FL — это колоссальный объем данных, который наглядно объясняет, почему этот материал официально признан мировым научным сообществом «золотым стандартом» адгезии (Dreweck et al., PMID: 34919728; Peumans et al., PMID: 37435814).

Поделиться этой информацией
URL публикации
Предыдущая публикация

Evaluation of Near-Infrared Transparent Sealants for Occlusal Sealing: An In Vitro Study.

Следующая публикация

The Effect of Immediate Dentin Sealing Using Different Universal Adhesives on the Bond Strength of Pretreated Monolithic Zirconia to Dentin and Microscopic Morphological Alterations.

Добавить комментарий

Ваш адрес email не будет опубликован. Обязательные поля помечены *

Смотреть далее